Command: CC.COM

  The small CC.COM "Clear Cache" program can help verify files written
  by UIDE and UHDD. Entering CC at a command prompt makes the
  caching driver "flush" its cache.
  Disk data (NOT data still in cache!) can then be compared v.s. the
  original output.
  Note that some CompactFlash cards cause CC to execute very slowly.

Syntax:

cc

Options:

  - none -

Comments:

  For all switches in each driver, a dash may replace the slash and lower
  case letters may be used if desired.
  For more information read "README.txt" in drivers.zip.

Examples:

  Comment: There are new closed source drivers for UHDD.SYS (=XHDD.SYS)
  and UVD2.SYS (=XDVD2.SYS) which may have other options. So please do
  not rely on the options in the examples!
  A) A small real-mode system that needs only XMS may use this
    CONFIG.SYS/FDCONFIG.SYS example file:
       ..
       ..
     DOS=HIGH
     DEVICE=C:\FD\BIN\XMGR.SYS /Rnn             ;R if DOS "games" need it
       ..
       ..  Int 13h drivers cached by UHDD load now.
       ..
     DEVICE=C:\FD\BIN\UHDD.SYS /S20 /H /O       ;Min. 20 MB recommended
     DEVICE=C:\FD\BIN\UDVD2.SYS /D:BLURAY1 /H   ;Must load after UHDD
     DEVICE=C:\FD\BIN\RDISK.COM /S5 /F          ;Optional. If not used,
                                                ; UHDD/UDVD2 can issue /F
       ..
       ..  Further CONFIG.SYS commands can be given here.
       ..
    cc                                        ;Cleans the cache of UHDD

  B) Real-mode systems with V3.70+ UMBPCI and XMGR do not need the LOWDMA
     driver, as XMGR has an "I-O Catcher" for UMBPCI. This scheme takes
     NO low memory if /W can be used (MS-DOS etc.) or only 544 low memory
     bytes without /W (PC-DOS etc.). XMGR and other drivers load direct
     to UMBPCI "Shadow RAM"! Systems which permit multiple providers of
     upper memory (MS-DOS, PC-DOS, etc.) can also load an "EMM" driver as
     shown below, to map the B000-B7FFh "Monochrome Graphics" area as 32K
     more upper memory. For more SERIOUS protected-mode notes, please
     READ Section 6 below! An example CONFIG.SYS file is:
       ..
       ..
     DOS=HIGH,UMB
     DEVICE=C:\FD\BIN\UMBPCI.SYS
     DEVICE=C:\FD\BIN\XMGR.SYS /W /Rnn        ;W only when permitted!
                                              ;R <= 15.5 MB with JEMM!
     DEVICE=C:\FD\BIN\JEMM386.EXE I=B000-B7FF X=C800-EFFF ...   ;Optional
       ..
       ..  Int 13h drivers cached via UHDD load now
       ..  and can be loaded in UMBPCI upper memory.
       ..
     DEVICEHIGH=C:\FD\BIN\UHDD.SYS /S200 /H /O    ;Fast 200 MB cache
     DEVICEHIGH=C:\FD\BIN\UDVD2.SYS /D:CDROM1 /H  ;Must load after UHDD
     DEVICEHIGH=C:\FD\BIN\RDISK.COM /S50 /F       ;Optional. If unused,
                                               ; UHDD/UDVD2 can issue /F
       ..
       ..  Further CONFIG.SYS commands can be given here.
       ..
    cc                                        ;Cleans the cache of UHDD

  C) A protected-mode system with XMGR and an "EMM" driver can use XMGR's
     "boot", taking a minimum 304 bytes of low memory for a 24-entry "XMS
     Handles" table, plus any low memory the "EMM" driver may need. For
     more SERIOUS protected-mode notes, please READ Section 6 below! A
     CONFIG.SYS example file is:
       ..
       ..
     DOS=HIGH,UMB
     DEVICE=C:\FD\BIN\XMGR.SYS /B /N24 /R15.5     ;24 Handle XMGR "boot"
                                               ;R <= 15.5 MB with JEMM!
     DEVICE=C:\FD\BIN\JEMM386.EXE I=B000-B7FF ...
     DEVICEHIGH=C:\FD\BIN\XMGR.SYS                ;Loads the runtime XMGR
       ..
       ..  Int 13h drivers cached by UHDD load
       ..  now and can load into upper memory.
       ..
     DEVICEHIGH=C:\FD\BIN\UHDD.SYS /S400 /H /O /P ;Optimal 400 MB cache
     DEVICEHIGH=C:\FD\BIN\UDVD2.SYS /D:MYDVD /H   ;Must load after UHDD
     DEVICEHIGH=C:\FD\BIN\RDISK.COM /S125 /F      ;Optional. If unused,
                                               ; UHDD/UDVD2 can issue /F
       ..
       ..  Further CONFIG.SYS commands can be given here.
       ..
    cc                                        ;Cleans the cache of UHDD

  In each example above, UDVD2 must load after UHDD, so UDVD2 will "find"
  UHDD in memory and call it for CD/DVD file caching.

  Users that need RDISK with a specific drive letter may delay loading it
  until AUTOEXEC.BAT / FDAUTO.BAT is run. If /F or /G are also needed
  for DOS games, RDISK must issue them from AUTOEXEC, since it is then
  the last of these drivers to load. Whenever RDISK is used, AUTOEXEC.BAT
  must also issue commands to copy all RDISK programs and data up to the
  RAM-disk, as XMS memory is LOST when PCs shut down! Such copies require
  little time.

  If UHDD and RDISK will both run, users must balance how much XMS memory
  the drivers take. UHDD can set a 400-MB cache, as in example C above,
  and RDISK can request 125-MB of XMS for its programs, "fast" data files
  and compiler TEMP files. Such sizes should be optimal on most systems
  but can be adjusted up or down, as desired. All remaining XMS memory
  is left free for use by other programs. The basic "plan" is for RDISK
  to hold programs and high-speed files, while UHDD then caches "regular"
  data files. Properly balanced use of XMS memory will give a VERY fast
  DOS system!

Command: CC.COM

Syntax:

Options:

Comments:

Examples:

See also: